Request Estimate

 

Just about every person seems to have their own individual beliefs on the subject of How to Install a Bathtub Yourself.

Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging job. If the old tub is easily obtainable, the task can move immediately; if you need to open a wall to get rid of the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Ensure you have actually certified on your own for the work as well as fit attempting it. Instead of employing a contractor to take over a halfway-completed project, it is much better to take into consideration using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your washroom if you have actually already purchased a new tub and do not require to transform the plan of your previous supply of water pipes.
Your tools as well as product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin making certain that the washing machines are in place in between the faucet and also the sink. Protect the tap in place with the producer offered backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former type needs to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Mounting the Bathtub

Using both wooden boards under its feet, put the bath tub in the needed placement. The wood boards are useful in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four little points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub till the spirit level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Switch on the water supply as well as check all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as additionally check the overflow electrical outlet as well as the normal outlet for leaks.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub needs to wait until the tub has actually been used a minimum of once as this will settle it right into its last placement.

 

 

Preparing for the Installation

Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.

 

 

Tiling Around the Tub

In the area where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, resulting in complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I was introduced to that article about Tools You Need to Install a New Bathtub from a good friend on a different web page. Sharing is nice. One never knows, you may just be doing someone a favor. Thanks a lot for your time. Please visit our site back soon.

Hot water issue? Call!